This is the equalization unit in front of the compressors. Now, for setting the first equalization: 7. Д«elow is a photo of the effects chain for mastering: However, as always in audio production, Shouldn't be too much to do and Don'ts: in some situations the aforementioned may be exactly the effect that the one after, but in a normal mastering situation, cutoff frequencies could be better done before and after increasing compression. For example, if you boost some low frequencies before compression, raise its maximum level and the compressor will probably react to these picks by trying to attenuate them.

Why? Due to the EQ setting it affects a bit how compression behaves. Now, a few words about the order of the plugins in the mixer: it might be a good idea to put the EQ that is used for cutting, before compression and equalization is used to boost, after compression. Fruity Limiter to maximize the volume of the whole mix.Д«asically, this set of plugins are enough to master your song successfully. Fruity Parametric EQ 2 to boost frequencies. Fruity Compresor Multibanda to fine tune the volume level in areas that are still too loud or in the mix (if that is so). Fruity Compresor to make sure that the dynamic range of the entire mix is вЂ‹вЂ‹balanced so that there are no big differences also between the quieter and louder parts. Open the mixer and add these plugins in the following order for the tracks on the master FX mixer:ДЇruity Parametric EQ 2 for cutting off unwanted frequencies.

Create another empty project in FL Studio and import the WAV mix into a playlist. Normalization increases the amplitude of the wave so that the highest pick is at the maximum level of 100% possible. That is just to prevent the song from cutting off abruptly as there may be a reverb tail or delay effect that keeps replaying after the actual song has ended. Create a very short fade out at the end of the song (if required) Create a new empty project in FL Studio and open your song in EdisonД¬ut unnecessary silence at the end or beginning of the song (in your case). This is the configuration that I am using usually:Дў. Use the highest possible quality for rendering. However, if you decide to use format 32 bits floating, you don't have to worry about clipping.ДЇurther, it's best not to use any compressor or limiter on the main track mixer when exporting. This is to avoid the appearance of clipping of the exported WAV. Export your mix to WAVД«efore exporting your mix, It is recommended to set the mixer of the master track volume level to all-6.0dB вЂ“8.0dB. Personally, I like to keep mixing and mastering as separate projects, so i am using method 2. There are actually two ways to master your songs in FL Studio: 1.) You can master the song while you are mixing or 2) you can export the song to a WAV file, create a new empty project and import it back to. Preparing the song for mastering and getting to work Please note that I have adjusted the settings for one of your own songs, but you can start with it and modify it according to your own song. This tutorial is as a starting point and introduction to a set of tools that can be used for this final process.ДЄt the end of this tutorial the FL Studio file is also being shared (Mixer) State in which I have set the plugin of the FX chain so that I can start the mastering process immediately. With all this said, now I am going to show a method that a US producer personally uses to masterizar their songs. It all depends on the audio material you have and what you want to achieve with the mastering. Each combination is different and that is why the mastering tools must be adjusted according to the situation. I have to say however that it is not really вЂњpress a button and goвЂќ O вЂњa fit that fits allвЂќ for mastering. There is a wide range of VST plugins that you can use for mastering and even tons of presets to get you started. Your song needs to sound as good and balanced as possible before going to the mastering stage. So before you start experimenting with mastering, you need to learn to mix. The truth is that if the song is little mixed, or the mastering is going to be done in an amateur way it will not end well, it is included, it may be worse. Keep in mind that mastering goes hand in hand with the mix. After masterizar, your song must be ready to be heard by the public. He is also preparing a song for the right medium. It is a process of improving the sound quality of your song with a set of tools such as equalizer, compressor and limiter. Mastering is the last step in music production.

How to master in fl studio